Products

Simple. Reliable. Bulletproof.

The TriggerLink Base is a plug-and-play 12V trigger to IR blaster that lets your modern AV processor control legacy IR-only equipment automatically. When your processor powers on and sends a 12V trigger signal, TriggerLink learns and fires the exact IR power-on command to your amplifier, receiver, or any IR-controlled device. No apps. No WiFi. No programming. Just connect and go.

Features

• 12V trigger input with optical isolation
• IR learn mode — learns any IR power command
• IR blaster output via 3.5mm jack
• Feedback sense input for power-state verification
• Three 3.5mm jacks total (trigger in, IR out, feedback in)
• Side-firing status LED — Kingbright WP710A10SRD, right-angle 3mm through panel
• Compact Hammond RL6175BK enclosure (92 × 38 × 31mm)
• No WiFi or app required
• Designed for AV installers

Specifications

Trigger Input	12V DC via 3.5mm mono jack, optically isolated
IR Output	940nm via 3.5mm jack (IR bug included)
IR Receiver	TSOP34338 (38kHz demodulator)
Feedback Input	12V sense via 3.5mm mono jack
Total Jacks	3 (trigger in, IR out, feedback in)
Power	USB-C (5V)
Enclosure	Hammond RL6175BK (92 x 38 x 31mm)
Weight	45g
Made In	USA

Full trigger automation. Two devices. Three zones. One button.

The TriggerLink Pro is a full-featured trigger automation controller that bridges two independent IR-controlled devices and up to three 12V-triggered amplifiers into a single automatic power sequence. When your source processor fires its 12V trigger, TriggerLink Pro walks through every connected device one at a time — waiting the configured per-device delay (2, 3, or 5 seconds — set via DIP switch) between each — so each amplifier and IR device powers on cleanly without overlapping inrush current. Three 12V trigger outputs fire in turn, followed by two independently-programmed IR commands to your legacy devices. Two feedback sense inputs — one per IR device — confirm each device actually powered on, with real-time blue Sense LEDs showing device status at a glance. On shutdown, the sequence runs in reverse so devices power down in the opposite order they came up.

Features

• 3× 12V trigger outputs, fired sequentially one device at a time
• 2× independently-programmed IR bug outputs — control two IR devices
• 2× feedback sense inputs (one per IR device) for power-state verification
• 8 front panel LEDs grouped by function (Power, Sense, Learn, Trigger) — vertical PCB LEDs with Bivar 8-element light-pipe strip for a clean, flush front face
• Configurable per-device delay via DIP switch: 2, 3, or 5 seconds between each device
• Reverse power-off sequence — devices shut down in opposite order
• Single Learn button cycles 4 EEPROM slots (Dev 1 ON/OFF, Dev 2 ON/OFF)
• Real-time auto-sensing — blue Sense LEDs mirror live device power state
• Supports NEC, Sony SIRC, RC5, RC6, Samsung, and Panasonic IR protocols
• EEPROM-stored IR codes survive power loss
• USB-C for firmware updates and debug

Specifications

Trigger Source Input	12V DC via 3.5mm mono jack, optically isolated
12V Trigger Outputs	3× 3.5mm jacks, fired sequentially (per-device DIP delay between each)
IR Bug Outputs	2× 3.5mm jacks, 940nm, independently programmed
IR Receiver	TSOP34338 (38kHz demodulator)
Feedback Sense Inputs	2× with optical isolation
Front Panel LEDs	8 vertical 3mm LEDs (1 green, 2 blue, 2 yellow, 3 red) behind Bivar 8-element light-pipe strip
Per-Device Delay	DIP switch: 2, 3, or 5 seconds between each device
Power Sequence	Staggered on-then-reverse-off, per-device
Power Input	12V DC, 5.5×2.1mm barrel jack
Firmware Updates	USB-C
Current Draw	~140mA steady, ~220mA peak
Enclosure	Hammond RL6225BK (125 × 80 × 50mm)
Patent Status	Patent Pending
Made In	USA